The ensue is full way description of disassembly/reassembly. In this manual is listed according to the disassembly procedures. If you find the certain unit or assembly, please consult it’s name by the picture in the "Samsung CLX-2160 Service Repair Manual"
Main components of Samsung CLX-2160 printer include: Cover, ITB (Image Transfer-Bell), Fuser unit, HVPS (High Voltage Power Supply) board, main PBA (card formater), SMPS board (Switched-mode power supply), LSU (Laser Scanning Unit), Holder Pad, transfer roller, OPE PBA, pick up roller, ADF or RADF Unit
The coming is disassemble (removable) components Samsung printer CLX-2160 printer manual.
I. How to remove cover
This section is description how to open all of the covers (top cover, front cover, left cover, right cover, rear cover).
1. Move out the paper tray.
2. Open rear cover & remove 5 screws as shown below
3. take away dummy rear cover in the direction of arrow.
4. Open front cover and remove 2 screws. Then remove front cover
5. Open the rear cover and apply light pressure to the front side of it. And then remove the Right cover as show below
6. The same as step 5, remove left cover
7. Push down MP Unit & pull from left to light to remove dummy front cover out of frame
8. Move out recover cover
II. How to remove Scan unit
1. Unplug 3 connectors with main PBA (card formatter)
2. Open the Scan Unit and press light to the right of the Duct-Fan.
3. take away the hinge of the Jam cover
4. take away 2 Stopper-Scans by push it left to right
5. Lift the scan unit & remove 2 Stopper-Scan then remove it
III. How to remove the Middle unit Cover
1.Unplug connector whit the Fan.
2. Unplug connector with USB host & main PBA
3. Take out jam cover & 4 screws from the Middle Unit Cover.
4. Remove Fan on the left of Middle Unit Cover.
5. Move out 2 screws.
6. Take out Joint PBA.
7. Take out Actuator-Outfull and Sensor.
IV. How to remove Fuser unit
1. Remove rear cover (refer to I)
2. Move out 4 screws on the Fuser.
3. Push the Holder Shaft Fuser from left to right
4. Take out Fuser unit out of the frame
Caution: The fuser is so hot. So, You should turn your printer off & please wait until your printer to cool before remove it.
V. How to remove LSU (Laser Scanning Unit)
1. Move out the midle cover (Refer VII)
2. take away the 3 screws
3. Unplug 2 flat cable & the remove the LSU Unit.
VI. How to remove HVPS board (High Voltage Power Supply) board
1. Move out the left cover(Refer to I).
2. Move out 6 screws
3. Take out the HVPS board
VII. How to remove main PBA (card formater)
1. take away the right cover. (Refer I)
2. take away 4 screws from the main PBA bracket
3. Unplug the all jack connectors. And remove the main PBA (card formater).
VIII. How to remove SMPS board (Switched-mode power supply)
1. Move out the right cover. (Refer to I)
2. Move out 4 screws from the SMPS board.
3. take away all connectors from the SMPS & then remove the SMPS (Switched-mode power supply) board.
IX. How to remove drive unit
1. Move out right cover (refer to I).2. take away main PBA, SMPS (Refer to VII, VIII )3. Take out 8 screws4. Remove drive unitX. How to remove transfer roller1. Take out rear cover (refer to 1)2. Move out 2 screws3. Pull back the hook, which holds the tramsfer foller, & remove itMore details to disassemble (removable) components Samsung printer CLX-2160 printer, you view in "Samsung CLX-2160 Service Repair Manual".
Samsung CLX-2160 Service Repair Manual document very important with technician when meliorate, disassemble (removable) components the Samsung printer CLX-2160 printer. "Samsung CLX-2160 Service Repair Manual" guide technician remove & Install components internal Samsung printer CLX-2160 printer, providing them knowledge intensive the component, how to take apart & meliorate bugs in the process of using Samsung printer CLX-2160 printer that the user themselves can not repair.You can Price it at the coming:
Cost for Samsung printer CLX-2160 Service Repair Manual: $ 5
To get Service Repair Manual, pls payment with ensue info :
Paypal : helinacare@gmail.com