Service Manuals - Repair printer - Fix printer by Firmware reset fix

When you print a document, nothing printed. Smart Panel program window accurrence message "The printer does not print"
Currently, Color laser printers CLP-300 is being using quite extensively. Samsung printer CLP-300 printer also has advantages coming: print speed, toner saving and easy to run.
However, we can not avoid the damage of your printer as some components of your printer caused in during run.
When your printer experiences an error, the control panel will indicate an error message with the indicator lights & the Smart Panel program window will accurrence to show the printer’s status or errors. Find the light pattern below that matches your printer light pattern and follow the solutions to clear the error.

The origin of Pages are coming out curled or wrinkled by HP LaserJet 3015 Printer:

– The printer is not receiving power.
– The pritner is not selected as the default printer
– Check your printer for the ensuing:
+ The printer cover is not closed
+ Paper is jammed
+ No paper is loaded
+ A toner cartridge is not Install
– The printer may be in manual feed mode & out paper.
– The connect cable between the computer & your printer is defective.
– The post setting is incorrect
– The printer may be configured incorrectly
– The printer driver may be incorrectly installed.

Instruction to fix Pages are ensue out curled or wrinkled by HP LaserJet 3015 Printer(See more details in HP LaserJet 3015 Service Repair Manual):

– Check the power cord connections. Check the power switch & the power source.
– Select Samsung printer CLP-300 series as your default printer.
– After locating the problem, clear it. If a printer system error occurs, contact your service representative.
+ Close the printer cover

+ Clear the paper jam

+ Load paper
+ setup the toner printer cartridge
– Test the message on the Smart panel program window, add paper to the Tray & press the Stop button on the setup panel
– Disconnect your printer cable and reconnect it
– If possible, attach the cable to another computer/mac that is working properly and try to print a document. You can also try used a different printer cable.
– Test the Windows printer setting to yield sure that the print job is sent to the correct port. If the computer has more than one port, give sure that your printer is attached to the correct one.
– Test your printer properties to ensure that all of the print settings are correct.
– Reinstall the printer driver; see the soft ware section. Try printing a test pages
You can find solutions meliorate other errors of Samsung printer CLP-300 printer in "Samsung printer CLP-300 Service Repair Manual". The following is table LED status legend for Samsung CLP-300
Samsung printer CLP-300 Service Repair Manual document very important with technician when fix the Samsung printer CLP-300 printer. "Samsung printer CLP-300 Service Repair Manual" guide technician remove and install components internal Samsung printer CLP-300 printer, providing them knowledge intensive the component, how to take apart and restore bugs in the process of used Samsung printer CLP-300 printer that the user themselves can not mend.

When you print a document, nothing printed. Smart Panel program window presentation message "The printer does not print"(Samsung printer CLP-320/325). Cause of error "The printer does not print" are the cable plug in has occur problems, your printer not selected as the default printer, cover is not closed, your printer is malfunctioning …
Currently, Color laser printerss CLP-320/325 is being used quite extensively. Samsung printer CLP-310/315 printers also has advantages coming: Enjoy quality printouts, Polymerised toner, Ergonomic design, Easy to use, Easy Colour Manager, Easy Solution support.

However, we can not avoid the damage of the printer as some components of the printer caused in during operate.
When your printer experiences an error, the regulations panel will indicate an error message with the indicator lights & the Smart Panel program window will shows to show the printer’s status or errors. Find the light pattern below that matches the printer light pattern and follow the solutions to clear the error.

The origin of "The printer does not print" by Samsung CLP-320/325 Printer:

1. The printer is power off or not receiving.
2. The pritner is not selected as the default printer
3. Test the printer for the following:
+ The printer cover is not closed.
+ Paper is jammed.
+ No paper is loaded.
+ The toner printer cartridge is not installed.
4. The printer may be in manual feed mode and out of paper
5. The connection cable between the computer & the printer is disconnected properly.
6. The connection cable between the pc and your printer is defective.
7. The port setting is incorrect.
8. The printer may be configured incorrectly.
9. The printer driver may be incorrectly install.
10. The printer is malfunctioning.

Instruction to restore "The printer does not print" by Samsung CLP-320/325 Printer(See more details in Samsung printer CLP-320/325 Service Repair Manual):

1. Test the power cord connections. Test the power switch & the power source. If cause not the power cable, regenerate the power supply.
2. Select Samsung CLP-320/325 PCL 6 as your default printer in your Windows (Start-Printers and fax(Devices & Printers)-find to Samsung printer CLP-320 series-right click-choose "Set as default printer")
3. Repair printer cover, paper jam, no paper:
+ Close your printer cover.
+ Clear the paper jam.
+ Load paper.
+ setup the toner printer cartridge.
4. Test the message on the Smart Panel program window, add paper to the tray & press the Stop button on the setup panel.
5. Disconnect your printer cable & reconnect it.
6. If possible, attach the cable to another computer/mac that is working properly and print a job. You can also try using a different printer cable.
7. Test the Windows printer setting to yield sure that the print job is sent to the correct port. If the computer/mac has more than one port, yield sure that your printer is attached to the correct one.
8. Test the printer properties to ensure that all of the print settings are correct.
9. Repair the printer software. See the Software Section. Try printing a test pages.
10. Check the LEDs on the control panel to determine if the printer is indicating a system error.

You can find solutions restore other errors of Samsung printer CLP-320/325 printer in "Samsung CLP-320/325 Service Repair Manual".
Samsung printer CLP-320/325 Service Repair Manual document very important with technician when meliorate the Samsung printer CLP-320/325 printer. "Samsung CLP-320/325 Service Repair Manual" guide technician remove and installed components internal Samsung printer CLP-320/325 printer, providing them knowledge intensive the component, how to take apart and repair bugs in the process of using Samsung printer CLP-320/325 printer that the user themselves can not repair.

Samsung printer CLX-2160 has orrcur "Printed pages problems": No image, Light or faded print, Toner specks, Dropouts, Vertical lines, Gray background, Toner smear, Vertical repetitive defects, Background scatter, Misformed characters, Page skew, Curl or wave, Wrinkles or creases, Back of printouts are dirty, Black pages(Completely Black Image), Loose toner, Character Voids, Horizontal stripes, Curl, White Spots / Black Spots / Colored Spots
Currently, Color laser printers CLX-2160 is being used quite extensively. Samsung printer CLX-2160 printers also has advantages coming: Enjoy quality printouts, Polymerised toner, Ergonomic design, Easy to proceed, Easy Colour Manager, Easy Solution support.However, we can not avoid the damage of your printer as some components of the printer caused in during proceed.
The ensue, I will introduce three basic errors with printing quality problems of Samsung printer CLX-2160 printer and "How to restore it". With other print pages errors, you manifestation at "Samsung CLX-2160 Service Repair Manual"
1. Vertical black line & band on printed page for Samsung printer CLX-2160 Printer
Description Vertical black line & band: On the printed pages have straight thin black vertical line & dark black vertical band.
Error location: LSU unit, axis developer, transfer roller, OPC drum, ITB unit.

Cause of error "Vertical black line and band" on the printed page:

– LSU unit has occur problem or simply dirty
– Damaged develop roller in the developer. Deformed Doctor-blade or cleaning blade.
– Scratched surface of the discharge roller in the developer.
– Partly depression or deformation on the surface of the transfer roller
– Test if the surface of the charge roller is scratched or contaminated.
– Test if there are grooves on the circumference of the OPC drum.
– Check if the cleaning blade is damaged.
– Check if paper transfer belt is damaged or contaminated.

How to fix(mend) "Vertical black Line and Band" on the printed pages for Samsung printer CLX-2160 Printer:

– Clean the LSU unit by soft cotton cloth & try to print. If printed page still faulty as initial you should change new LSU unit or contact a service representative.
– If causes are cause 2nd and 3rd, you need regenerate new axis developer & try to print
– If causes are cause 4nd, you need change transfer roller.
– Change the imaging unit & test again.
– Regenerate the ITB unit and check again.
2. Dark Image or black on printed page for Samsung printer CLX-2160 Printer
Description Dark Image or black: The printed page is dark or full black.
Error location: OPC drum, HVPS unit
Cause of error "Dark Image or black" on the printed page:
– No charge voltage in the HVPS board
– Charge voltage is not turned on due to the bad contact between power supply in the side of the developer and charge terminal of HVPS

How to fix(restore)"Dark Image or black" on the printed page for Samsung printer CLX-2160 Printer:

– Clean the high voltage charge terminal
– Test the state of the connector which connects the engine board & HVPS.
– Regenerate the HVPS if not solved by the on top of direction 1 & 2
3. Light image on printed pages for Samsung CLX-2160 Printer
Description: The printed pages is light & no ghost
Error location: Developer, HVPS
Cause of error "Light image" on the printed pages
– Develop roller is stained when the toner of developer printer cartridge is almost consumed
– Temperature in room is below than 10*C
– Bad contact caused by the toner dirty between the high voltage terminal in the HVPS & the one in the set
– Abnormalities output from the HVPS

How to fix(mend) error "Light image" on the printed page for Samsung printer CLX-2160 Printer:

– Replace the new developer & try to print out
– After printer is power on, wait 30 minutes then start printing
– Clean up the dirty area by the toner
– Replace the new HVPS if the problems are not solved by the above four directions
4. Vertical White Line
Description : White vertical voids in the image.

Cause of error "Vertical white line" on the printed pages:

– Check if the LSU window or internal lenses of LSU is contaminated.
– Check if there are scratches on the circumference of the OPC drum.
– Test if there are scratches on the circumference of the developing roller.
– Test if paper transfer belt is damaged or contaminated.
How to fix(restore) error "Vertical white line" on the printed pages for Samsung CLX-2160 Printer:
– Clean the LSU window with recommended cleaner(IP A). Clean the window with a clean cotton swab. If dirt is inside the LSU, regenerate the LSU.
– Renew the imaging unit & test again- Change the ITB unit & test again.
Samsung CLX-2160 Service Repair Manual document very important with technician when meliorate, disassemble (removable) components the Samsung printer CLX-2160 printer. "Samsung CLX-2160 Service Repair Manual" guide technician remove and setup components internal Samsung printer CLX-2160 printer, providing them knowledge intensive the component, how to take apart & restore bugs in the process of using Samsung printer CLX-2160 printer that the user themselves can not restore.
More details, you manifestation in "Samsung CLX-2160 Service Repair Manual". You can Price it at the ensuing:
fee for Samsung printer CLX-2160 Service Repair Manual: $ 5
To download Service Repair Manual, pls payment with ensue info :
Paypal : helinacare@gmail.com

Paper jam is problem popular of printers. The ensue is paper jam error and description how to meliorate “Paper Jam” errors Samsung printer ML-84/85/85G/1010H/1520P

When paper jammed, The message error shown on smart panel of computer or flashing yellow light & printer does not print:

– Paper Jam 0 Open/Close Door
– Paper Jam 1 Check inside
– Paper Jam 2

I. The message error shown on Smart panel of pc: Paper Jam 0 Open/Close Door

Description"Paper Jam 0 Open/Close Door": Printer does not print and paper not exited paper tray.
Error location: Jam at paper feeder input tray
Cause of error "Paper Jam 0 Open/Close Door":
– Wrinkled paper
– Paper too thick or too thin
– Pick-up roller of document feeder input tray has error: worn, torn, dirty.
– Feed sensor in paper tray occours error
– The paper is not tied into the printer.
Clear "Paper Jam 0 Open/Close Door"
1. Take out the paper tray .
2. take away paper jam.
3. Put in the paper tray & print check.

How to fix(restore)"Paper Jam 0 Open/Close Door" error of Samsung printer ML-84/85/85G/1010H/1520P:

– Clean Pick-up roller or change Pick-up roller by soft cloth. If still error, replace rubber surface of Pick-up roller.
– Change feed sensor in paper tray
– Put in paper good quality in to paper tray

II. The message error shown on Smart panel of pc: Paper Jam 1 Open/Close the door

Description JAM 1: Paper does not exit.
Error location: Paper jammed in front of, inside the fuser, in the discharge roller or in the fuser just after passing through the Actuator-Feed.
Cause of error “Paper jam 1 Open/close the door” Samsung ML-84/85/85G/1010H/1520P
– Exit sensor may be error
– SMPS occur errors: power source is weak not enough yield the fuser unit heat up
– Main PBA has occur problem: Firmware error
– Reassembly components of toner printer cartridge are incorrect & them don’t rotate. Give paper does not pass toner cartridge
Clear jam
1. Open front cover
2. Take out toner printer cartridge
3. Move out paper jam.
How to fix(mend) “Paper jam 1 Open/close the door” error of Samsung printer ML-84/85/85G/1010H/1520P
– Clean exit sensor (it’s location at back side & on the right) by soft cloth. If still error, you must replace exit sensor
– Change SMPS board and main PBA
– take away components of toner cartridges & reassembly to correct. If some components is corrupt, you must renew new genuine toner cartridge

III. The message error shown on Smart panel of pc: Paper jam 2

Description Paper Jam 2: Part of the paper has to exit
Error location: Paper jammed inside the fuser.
Cause of error “Paper Jam 2” of Samsung ML-84/85/85G/1010H/1520P
– Exit sensor may be error: It may stick open or return only slowly due to contamination be paper debris or foreign objects.
– Paper is wet, too thick, too thin or wrinkled.
– Spring of a Guide claw is broken away, damaged or deformed
– Fuser unit dirty (Heat-Roller or Pressure-Roller are dirty by toner powder or dust)
Clear Paper Jam 2
1. Open rear cover
2. Take out paper jam one way carefully and print test
How to fix(fix) “Paper Jam 2” error of Samsung printer ML-84/85/85G/1010H/1520P
– Clean exit sensor (it’s location at back side and on the right) by soft cloth with alcohol. If still error, you must regenerate exit sensor
– Choose good quality paper
– Replace spring of a Guide.
– Disassemble fuser unit and remove the jammed paper, & clean the surface of the pressure roller with dry soft cloth.
More details, you presentation in "Samsung printer ML-84/85/85G/1010H/1520P Service Repair Manual".
Samsung printer ML-84/85/85G/1010H/1520P Service Repair Manual document very important with technician when meliorate, disassemble (removable) components the Samsung printer ML-84/85/85G/1010H/1520P printer. "Samsung printer ML-84/85/85G/1010H/1520P Service Repair Manual" guide technician remove & installed components internal Samsung ML-84/85/85G/1010H/1520P printer, providing them knowledge intensive the component, how to take apart and mend bugs in the process of using Samsung printer ML-84/85/85G/1010H/1520P printer that the user themselves can not restore.
You can Price it at the coming:
pay for Samsung printer ML-84/85/85G/1010H/1520P Service Repair Manual: $ 5
To get Service Repair Manual, pls payment with ensue info :
Paypal : helinacare@gmail.com

Samsung CLP-500N/550 has orrcur "Printed pages problems": No image, Light or faded print, Toner specks, Dropouts, Vertical lines, Gray background, Toner smear, Vertical repetitive defects, Background scatter, Misformed characters, Page skew, Curl or wave, Wrinkles or creases, Back of printouts are dirty, Black pages(Completely Black Image), Loose toner, Character Voids, Horizontal stripes, Curl, White Spots / Black Spots / Colored Spots
Currently, Color laser printers CLP-500N/550 is being using quite extensively. Samsung printer CLP-500N/550 printers also has advantages ensue: Enjoy quality printouts, Polymerised toner, Ergonomic design, Easy to proceed, Easy Colour Manager, Easy Solution support.
However, we can not avoid the damage of the printer as some components of your printer caused in during put to work.

The following, I will introduce three standard errors with printing quality problems of Samsung printer CLP-500N/550 printer & "How to meliorate it". With other print page errors, you manifestation at "Samsung CLP-500N/550 Service Repair Manual"

1. Vertical black line & band on printed pages for Samsung CLP-500N/550 Printer
Description Vertical black line & band: On the printed pages have straight thin black vertical line & dark black vertical band.
Error location: LSU unit, axis developer, transfer roller, OPC drum, ITB unit.

Cause of error "Vertical black line and band" on the printed page:

– LSU unit has occur problem or simply dirty
– Damaged develop roller in the developer. Deformed Doctor-blade or cleaning blade.
– Scratched surface of the discharge roller in the developer.
– Partly depression or deformation on the surface of the transfer roller
– Test if the surface of the charge roller is scratched or contaminated.
– Check if there are grooves on the circumference of the OPC drum.
– Check if the cleaning blade is damaged.
– Check if paper transfer belt is damaged or contaminated.

How to fix(fix) "Vertical black Line and Band" on the printed pages for Samsung printer CLP-500N/550 Printer:

– Clean the LSU unit by soft cotton cloth and try to print. If printed page still faulty as initial you must regenerate new LSU unit or contact a service representative.
– If causes are cause 2nd & 3rd, you need change new axis developer and try to print
– If causes are cause 4nd, you need regenerate transfer roller.
– Change the imaging unit & check again.
– Replace the ITB unit and check again.
2. Dark Image or black on printed pages for Samsung printer CLP-500N/550 Printer
Description Dark Image or black: The printed page is dark or full black.
Error location: OPC drum, HVPS unit

Cause of error "Dark Image or black" on the printed page:

– No charge voltage in the HVPS board
– Charge voltage is not turned on due to the bad contact between power supply in the side of the developer & charge terminal of HVPS

How to fix(fix)"Dark Image or black" on the printed pages for Samsung CLP-500N/550 Printer:

– Clean the high voltage charge terminal
– Check the state of the connector which connects the engine board & HVPS.
– Renew the HVPS if not solved by the on top of direction 1 & 2
3. Light image on printed page for Samsung printer CLP-500N/550 Printer
Description: The printed page is light and no ghost
Error location: Developer, HVPS
Cause of error "Light image" on the printed pages
– Develop roller is stained when the toner of developer printer cartridge is almost consumed
– Temperature in room is below than 10*C
– Bad contact caused by the toner dirty between the high voltage terminal in the HVPS and the one in the set
– Abnormalities output from the HVPS
How to fix(mend) error "Light image" on the printed page for Samsung printer CLP-500N/550 Printer:
– Change the new developer & try to print out
– After printer is power on, please wait 30 minutes then start printing
– Clean up the dirty area by the toner
– Replace the new HVPS if the problems are not solved by the above four directions
4. Vertical White Line
Description : White vertical voids in the image.
Cause of error "Vertical white line" on the printed page:
– Test if the LSU window or internal lenses of LSU is contaminated.
– Test if there are scratches on the circumference of the OPC drum.
– Check if there are scratches on the circumference of the developing roller.
– Test if paper transfer belt is damaged or contaminated.
How to fix(restore) error "Vertical white line" on the printed pages for Samsung printer CLP-500N/550 Printer:
– Clean the LSU window with recommended cleaner(IP A). Clean the window with a clean cotton swab. If dirt is inside the LSU, change the LSU.
– Regenerate the imaging unit and check again
– Replace the ITB unit and test again.

Samsung printer CLP-500N/550 Service Repair Manual document very important with technician when meliorate, disassemble (removable) components the Samsung printer CLP-500N/550 printer. "Samsung CLP-500N/550 Service Repair Manual" guide technician remove and setup components internal Samsung printer CLP-500N/550 printer, providing them knowledge intensive the component, how to take apart and mend bugs in the process of used Samsung CLP-500N/550 printer that the user themselves can not fix.
More details, you view in "Samsung CLP-500N/550 Service Repair Manual". You can pay it at the following:
Cost for Samsung printer CLP-500N/550 Service Repair Manual: $ 5
To download Service Repair Manual, pls payment with coming info :
Paypal : helinacare@gmail.com

Samsung printer SL-M337X/M387X/M4070 has orrcur "Printing quality problem": No image, Light or faded print, Toner specks, Dropouts, Vertical lines, Gray background, Toner smear, Vertical repetitive defects, Background scatter, Misformed characters, Page skew, Curl or wave, Wrinkles or creases, Back of printouts are dirty, Black pages(Completely Black Image), Loose toner, Character Voids, Horizontal stripes, Curl, White Spots / Black Spots / Colored Spots

Currently, Samsung printer SL-M337X/M387X/M4070 printer is being using quite extensively. Samsung printer SL-M337X/M387X/M4070 printers also has advantages ensuing: Enjoy quality printouts, Polymerised toner, Ergonomic design, Easy to put to work, Easy Solution support.However, we can not avoid the damage of the printer as some components of your printer caused in during use.
The ensuing, I will introduce three basic errors with printing quality problems of Samsung printer SL-M337X/M387X/M4070 printer & "How to fix it". With other print page errors, you appear at "Samsung SL-M337X/M387X/M4070 Service Repair Manual"

1. How to fix(fix) printing quality problems for Samsung printer SL-M337X/M387X/M4070: Vertical black line and band on printed page for Printer

Description Vertical black line & band: On the printed pages have straight thin black vertical line and dark black vertical band.
Error location: LSU unit, axis developer, transfer roller, OPC drum.

Cause of error "Vertical black line & band" on the printed pages:

– LSU unit has occur problem or simply dirty
– Damaged develop roller in the developer. Deformed Doctor-blade or cleaning blade.
– Scratched surface of the discharge roller in the developer.
– Partly depression or deformation on the surface of the transfer roller
– Check if the surface of the charge roller is scratched or contaminated.
– Test if there are grooves on the circumference of the OPC drum.
– Test if the cleaning blade is damaged.
– Test if paper transfer belt is damaged or contaminated.

How to fix(meliorate) "Vertical black Line and Band" on the printed page for Samsung SL-M337X/M387X/M4070 Printer:

– Clean the LSU unit by soft cotton cloth and try to print. If printed page still faulty as initial you should replace new LSU unit or contact a service representative.
– If causes are cause 2nd & 3rd, you need change new axis developer & try to print
– If causes are cause 4nd, you need regenerate transfer roller.
– Renew the imaging unit and check again.
– Regenerate the ITB unit & test again.

2. How to fix(fix) printing quality problems for Samsung printer SL-M337X/M387X/M4070: Dark Image or black on printed pages for Samsung printer SL-M337X/M387X/M4070 Printer

Description Dark Image or black: The printed pages is dark or full black.
Error location: OPC drum, HVPS unit

Cause of error "Dark Image or black" on the printed pages:

– No charge voltage in the HVPS board
– Charge voltage is not turned on due to the bad contact between power supply in the side of the developer and charge terminal of HVPS

How to fix(fix)"Dark Image or black" on the printed pages for Samsung printer SL-M337X/M387X/M4070 Printer:

– Clean the high voltage charge terminal
– Test the state of the connector which connects the engine board and HVPS.
– Change the HVPS if not solved by the on top of direction 1 and 2

3. How to fix(restore) printing quality problems for Samsung printer SL-M337X/M387X/M4070: Light image on printed page for Samsung printer SL-M337X/M387X/M4070 Printer

Description: The printed page is light and no ghost
Error location: Developer, HVPS

Cause of error "Light image" on the printed pages

– Develop roller is stained when the toner of developer cartridges is almost consumed
– Temperature in room is below than 10*C
– Bad contact caused by the toner dirty between the high voltage terminal in the HVPS and the one in the set
– Abnormalities output from the HVPS

How to fix(restore) error "Light image" on the printed page for Samsung printer SL-M337X/M387X/M4070 Printer:

– Change the new developer & try to print out
– After printer is power on, wait 30 minutes then start printing
– Clean up the dirty area by the toner
– Change the new HVPS if the problems are not solved by the above four directions

4. How to fix(restore) printing quality problems for Samsung SL-M337X/M387X/M4070: Vertical White Line

Description : White vertical voids in the image.

Cause of error "Vertical white line" on the printed page:

– Test if the LSU window or internal lenses of LSU is contaminated.
– Check if there are scratches on the circumference of the OPC drum.
– Test if there are scratches on the circumference of the developing roller.

How to fix(mend) error "Vertical white line" on the printed page for Samsung printer SL-M337X/M387X/M4070 Printer:

– Clean the LSU window with recommended cleaner(IP A). Clean the window with a clean cotton swab. If dirt is inside the LSU, regenerate the LSU.
– Replace the imaging unit & test again- Change the ITB unit and check again.
Samsung printer SL-M337X/M387X/M4070 Service Repair Manual document very important with technician when repair, disassemble (removable) components the Samsung printer SL-M337X/M387X/M4070 printer. "Samsung SL-M337X/M387X/M4070 Service Repair Manual" guide technician remove & install components internal Samsung SL-M337X/M387X/M4070 printer, providing them knowledge intensive the component, how to take apart and fix bugs in the process of using Samsung SL-M337X/M387X/M4070 printer that the user themselves can not mend.
More details, you manifestation in "Samsung SL-M337X/M387X/M4070 Service Repair Manual". You can Cost it at the coming:
Price for Samsung SL-M337X/M387X/M4070 Service Repair Manual: $ 5
To download Service Repair Manual, pls payment with ensue info :
Paypal : helinacare@gmail.com